E&TC / ECE · Healthcare electronics · Final year project
DIY Ventilator using Arduino with Blood Oxygen Sensing For COVID Pandemic
A low-cost ventilator built with an Arduino. DC motors squeeze a silicone ventilator bag from both sides at a controlled rate, while an SpO2 sensor and pressure sensor monitor the patient to prevent under- or over-ventilation.
What is the DIY Ventilator using Arduino with Blood Oxygen Sensing For COVID Pandemic project?
A low-cost ventilator built with an Arduino. DC motors squeeze a silicone ventilator bag from both sides at a controlled rate, while an SpO2 sensor and pressure sensor monitor the patient to prevent under- or over-ventilation.
Key facts
- Branch
- Electronics & Telecommunication (E&TC / ECE); also suits Mechatronics, Biomedical
- Type
- Final year project · Advanced
- Suitable for
- Diploma capstone and B.E / B.Tech final year
- Build time
- 6 to 8 weeks
- Estimated component cost
- ₹2,400 – ₹3,500
- Guidance from
- ₹9,999 (Hardware / IoT Final Year)
How the DIY Ventilator using Arduino with Blood Oxygen Sensing For COVID Pandemic works
- 12 V power adapter / step-down transformer supplies the circuit; a regulator gives the controller and sensors a steady 5 V.
- The Arduino Uno R3 reads the inputs, runs the decision logic written in C/C++ and drives the outputs.
- The Mini submersible water pump moves water for irrigation, dispensing or cooling.
- The DC geared motor provides the driving motion.
- The LEDs indicate status.
- The Buzzer gives an audible alert.
Block diagram
Controller
Arduino Uno R3Outputs
Mini submersible water pumpDC geared motorLEDsBuzzerComponents list and cost
Typical prices from Indian online stores and electronics markets (Lamington Road, Budhwar Peth, SP Road). Buy from one store where you can to save on shipping.
| Component | Qty | What it does | Approx. cost |
|---|---|---|---|
| Arduino Uno R3 | 1 | Reads the inputs, runs the decision logic written in C/C++ and drives the outputs. | ₹550 |
| Mini submersible water pump (12 V) | 1 | Moves water for irrigation, dispensing or cooling. | ₹180 |
| DC geared motor | 1 | Provides the driving motion. | ₹250 |
| LEDs (assorted) | 1 | Indicate status. | ₹20 |
| Buzzer | 1 | Gives an audible alert. | ₹20 |
| 12 V power adapter / step-down transformer | 1 | Supplies stable low-voltage power from the mains. | ₹250 |
| Passive components, PCB and wiring kit | 1 | Resistors (assorted), capacitors (assorted), PCB / breadboard and cables, connectors and jumper wires. | ₹310 |
| Wiring, PCB, soldering and enclosure | 1 | Project overhead | ₹450 |
| Demo model base / mounting board | 1 | Project overhead | ₹500 |
| Testing spares and replacements | 1 | Project overhead | ₹300 |
| Estimated total | Varies with brand, quality and city | ₹2,400 – ₹3,500 |
Prices are estimates for budgeting. We confirm the bill of materials when your design is frozen, and components are charged at actual cost with bills.
How much does this project cost?
| Option | What you get | Cost |
|---|---|---|
| Components only | You buy the parts and build it yourself | ₹2,400 – ₹3,500 |
| Hardware / IoT Final Year | Working model or guided build, Circuit diagram and bill of materials, Firmware / code with explanation | from ₹9,999 + components |
| Capstone Project (CPE) | Working project or model, Black book in MSBTE format, Step-by-step explanation | ₹9,999 + components |
| Diploma ITR | 100% working source code, Project report PDF, PPT | ₹1,999 + components |
No GST and no hidden charges. Use the cost calculator for a quote with your deadline and add-ons, or see all plans.
Download the project brief (PDF)
Summary, working, components and cost and viva questions on one branded PDF to show your guide or team. To get it developed, contact us on WhatsApp.
What you submit with this project
- Working model with circuit diagram and program code
- Project report or black book in your university's chapter order (block diagram, circuit, calculations, results)
- Presentation for the review and final viva
- Synopsis for topic approval, if your college asks for one
E&TC / ECE viva questions on this project
What is the aim of the DIY Ventilator using Arduino with Blood Oxygen Sensing For COVID Pandemic project?
A low-cost ventilator built with an Arduino. DC motors squeeze a silicone ventilator bag from both sides at a controlled rate, while an SpO2 sensor and pressure sensor monitor the patient to prevent under- or over-ventilation.
Explain the working of your project in short.
12 V power adapter / step-down transformer supplies the circuit; a regulator gives the controller and sensors a steady 5 V. The Arduino Uno R3 reads the inputs, runs the decision logic written in C/C++ and drives the outputs. The Mini submersible water pump moves water for irrigation, dispensing or cooling. The DC geared motor provides the driving motion.
What microcontroller is on the Arduino Uno and what are its key specifications?
The Uno uses the ATmega328P: 8-bit, 16 MHz clock, 32 KB flash, 2 KB SRAM, 14 digital I/O pins (6 PWM) and 6 analog inputs with a 10-bit ADC.
How is the pump switched by the controller?
Through a relay or MOSFET, because the pump runs at 12 V and draws more current than the controller pin can provide.
Why is a geared motor used?
The gearbox reduces speed and multiplies torque, so a small DC motor can move a vehicle or mechanism smoothly. Torque increases roughly by the gear ratio.
Why is a resistor connected in series with an LED?
It limits the current to a safe value (about 10–20 mA). Without it, the LED would draw too much current and burn out. R = (supply voltage − LED voltage) ÷ current.
What is the difference between an active and a passive buzzer?
An active buzzer has a built-in oscillator and beeps on DC. A passive buzzer needs a square wave from the controller, which allows different tones.
Explain the block diagram of your project.
The input section senses the real-world quantity, the Arduino Uno R3 processes it according to the program, and the output section displays the result and drives the actuators. The power supply section feeds every block.
Which communication protocols are used between the modules?
Analog inputs read by the ADC for the analog sensors. Each protocol was chosen because the module supports it and it uses the fewest pins.
What is the operating voltage of the circuit?
The controller and most sensors work at 5 V (ESP boards and some modules at 3.3 V). A 12 V adapter powers the board, and a regulator steps it down. Motors and relays get their own supply line so they do not reset the controller.
Is your system open-loop or closed-loop?
Mainly open-loop: the controller runs the actuators for a set time or number of steps. Adding a sensor for feedback would make it closed-loop and more accurate.
How do you ensure patient safety?
The device runs on low-voltage batteries, has no direct mains connection to the patient, uses isolated sensors and limits current through any electrode. Alarms are set for abnormal readings.
Related projects
Academic use: Project Buddyy offers mentoring, guidance and reference material for learning. You stay responsible for following your institution's academic integrity rules and for understanding everything you submit.
Want to build DIY Ventilator using Arduino with Blood Oxygen Sensing For COVID Pandemic?
Send your college, deadline and team size. We confirm the scope, cost and what you will submit.