E&TC / ECE · Embedded and digital electronics · Final year project
PC Based Home Automation Using PIC
Home automation from a PC using a PIC microcontroller. Commands sent over the serial port switch lights and fans, so the user can control them without leaving the desk.
What is the PC Based Home Automation Using PIC project?
Home automation from a PC using a PIC microcontroller. Commands sent over the serial port switch lights and fans, so the user can control them without leaving the desk.
Key facts
- Branch
- Electronics & Telecommunication (E&TC / ECE); also suits Mechatronics
- Type
- Final year project · Intermediate
- Suitable for
- Diploma capstone and B.E / B.Tech final year
- Build time
- 4 to 6 weeks
- Estimated component cost
- ₹2,200 – ₹3,300
- Guidance from
- ₹9,999 (Hardware / IoT Final Year)
How the PC Based Home Automation Using PIC works
- 12 V power adapter / step-down transformer supplies the circuit; a regulator gives the controller and sensors a steady 5 V.
- The Push buttons and switches provide manual inputs and the power switch.
- The PIC16F877A microcontroller with board handles the control logic, ADC readings and output switching.
- The Relay module switches mains or high-current loads such as lamps, pumps and fans from a low-voltage signal.
- The LEDs indicate status.
Block diagram
Inputs
Push buttons and switchesController
PIC16F877A microcontroller with boardOutputs
Relay moduleLEDsComponents list and cost
Typical prices from Indian online stores and electronics markets (Lamington Road, Budhwar Peth, SP Road). Buy from one store where you can to save on shipping.
| Component | Qty | What it does | Approx. cost |
|---|---|---|---|
| PIC16F877A microcontroller with board | 1 | Handles the control logic, ADC readings and output switching. | ₹380 |
| Push buttons and switches | 2 | Provide manual inputs and the power switch. | ₹80 |
| Relay module | 1 | Switches mains or high-current loads such as lamps, pumps and fans from a low-voltage signal. | ₹70 |
| LEDs (assorted) | 1 | Indicate status. | ₹20 |
| 12 V power adapter / step-down transformer | 1 | Supplies stable low-voltage power from the mains. | ₹250 |
| Lamps | 1 | Part from the design specification | ₹150* |
| Passive components, PCB and wiring kit | 1 | Crystal oscillator, resistors (assorted), capacitors (assorted), transistors / MOSFETs, cables, connectors and jumper wires, diodes, PCB / breadboard and ICs and IC sockets. | ₹445 |
| Wiring, PCB, soldering and enclosure | 1 | Project overhead | ₹450 |
| Demo model base / mounting board | 1 | Project overhead | ₹500 |
| Testing spares and replacements | 1 | Project overhead | ₹300 |
| Estimated total | Varies with brand, quality and city | ₹2,200 – ₹3,300 |
Prices are estimates for budgeting; items marked * depend on the exact size or model chosen. We confirm the bill of materials when your design is frozen, and components are charged at actual cost with bills.
How much does this project cost?
| Option | What you get | Cost |
|---|---|---|
| Components only | You buy the parts and build it yourself | ₹2,200 – ₹3,300 |
| Hardware / IoT Final Year | Working model or guided build, Circuit diagram and bill of materials, Firmware / code with explanation | from ₹9,999 + components |
| Capstone Project (CPE) | Working project or model, Black book in MSBTE format, Step-by-step explanation | ₹9,999 + components |
| Diploma ITR | 100% working source code, Project report PDF, PPT | ₹1,999 + components |
No GST and no hidden charges. Use the cost calculator for a quote with your deadline and add-ons, or see all plans.
Download the project brief (PDF)
Summary, working, components and cost and viva questions on one branded PDF to show your guide or team. To get it developed, contact us on WhatsApp.
What you submit with this project
- Working model with circuit diagram and program code
- Project report or black book in your university's chapter order (block diagram, circuit, calculations, results)
- Presentation for the review and final viva
- Synopsis for topic approval, if your college asks for one
E&TC / ECE viva questions on this project
What is the aim of the PC Based Home Automation Using PIC project?
Home automation from a PC using a PIC microcontroller. Commands sent over the serial port switch lights and fans, so the user can control them without leaving the desk.
Explain the working of your project in short.
12 V power adapter / step-down transformer supplies the circuit; a regulator gives the controller and sensors a steady 5 V. The Push buttons and switches provide manual inputs and the power switch. The PIC16F877A microcontroller with board handles the control logic, ADC readings and output switching. The Relay module switches mains or high-current loads such as lamps, pumps and fans from a low-voltage signal.
What are the features of the PIC16F877A?
It is an 8-bit RISC microcontroller with 8 KB flash, 368 bytes RAM, 33 I/O pins, an 8-channel 10-bit ADC, two PWM modules, USART, SPI and I2C.
Why is a pull-up resistor needed with a push button?
Without it the input pin floats and reads random values. The pull-up keeps it HIGH until the button connects it to ground.
Why is a relay used?
It electrically isolates the 5 V control circuit from the high-voltage load. The controller energises the coil through a transistor, and the contacts switch the load.
Why is a resistor connected in series with an LED?
It limits the current to a safe value (about 10–20 mA). Without it, the LED would draw too much current and burn out. R = (supply voltage − LED voltage) ÷ current.
How is 230 V AC converted to 5 V DC for the circuit?
A transformer steps down the voltage, a bridge rectifier converts AC to pulsating DC, a capacitor smooths it and a 7805 regulator gives a steady 5 V.
Explain the block diagram of your project.
The input section senses the real-world quantity, the PIC16F877A microcontroller with board processes it according to the program, and the output section displays the result and drives the actuators. The power supply section feeds every block.
Which communication protocols are used between the modules?
The sensors give digital or analog signals read directly by the controller's I/O and ADC pins, and outputs are driven through transistor or relay drivers.
What is the operating voltage of the circuit?
The controller and most sensors work at 5 V (ESP boards and some modules at 3.3 V). A 12 V adapter powers the board, and a regulator steps it down. Motors and relays get their own supply line so they do not reset the controller.
Is your system open-loop or closed-loop?
Mainly open-loop: the controller runs the actuators for a set time or number of steps. Adding a sensor for feedback would make it closed-loop and more accurate.
Related projects
Academic use: Project Buddyy offers mentoring, guidance and reference material for learning. You stay responsible for following your institution's academic integrity rules and for understanding everything you submit.
Want to build PC Based Home Automation Using PIC?
Send your college, deadline and team size. We confirm the scope, cost and what you will submit.