Electrical · Renewable energy · Final year project
Solar Power Bank with Wireless Charging
A folding solar power bank with wireless charging. Solar panels charge a lithium battery pack through a charge controller, and phones charge by wire or wirelessly through built-in coils.
What is the Solar Power Bank with Wireless Charging project?
A folding solar power bank with wireless charging. Solar panels charge a lithium battery pack through a charge controller, and phones charge by wire or wirelessly through built-in coils.
Key facts
- Branch
- Electrical Engineering (EE / EEE); also suits E&TC / ECE
- Type
- Final year project · Intermediate
- Suitable for
- Diploma capstone and B.E / B.Tech final year
- Build time
- 4 to 6 weeks
- Estimated component cost
- ₹3,300 – ₹4,900
- Guidance from
- ₹9,999 (Hardware / IoT Final Year)
How the Solar Power Bank with Wireless Charging works
- Rechargeable battery and Solar panel supply the circuit; a regulator gives the controller and sensors a steady 5 V.
- The Arduino Uno R3 reads the inputs, runs the decision logic written in C/C++ and drives the outputs.
- The LEDs indicate status.
Block diagram
Controller
Arduino Uno R3Outputs
LEDsComponents list and cost
Typical prices from Indian online stores and electronics markets (Lamington Road, Budhwar Peth, SP Road). Buy from one store where you can to save on shipping.
| Component | Qty | What it does | Approx. cost |
|---|---|---|---|
| Arduino Uno R3 | 1 | Reads the inputs, runs the decision logic written in C/C++ and drives the outputs. | ₹550 |
| LEDs (assorted) | 1 | Indicate status. | ₹20 |
| Rechargeable battery (12 V 1.3–7 Ah) | 1 | Stores energy and supplies power when mains is absent. | ₹650 |
| Solar panel (10–20 W) | 1 | Converts sunlight into electricity to power or charge the system. | ₹900 |
| Charge controller module | 1 | Charges the battery safely and stops overcharging. | ₹250 |
| Passive components, PCB and wiring kit | 1 | Resistors (assorted), capacitors (assorted), PCB / breadboard and cables, connectors and jumper wires. | ₹310 |
| Wiring, PCB, soldering and enclosure | 1 | Project overhead | ₹450 |
| Demo model base / mounting board | 1 | Project overhead | ₹500 |
| Testing spares and replacements | 1 | Project overhead | ₹300 |
| Estimated total | Varies with brand, quality and city | ₹3,300 – ₹4,900 |
Prices are estimates for budgeting. We confirm the bill of materials when your design is frozen, and components are charged at actual cost with bills.
How much does this project cost?
| Option | What you get | Cost |
|---|---|---|
| Components only | You buy the parts and build it yourself | ₹3,300 – ₹4,900 |
| Hardware / IoT Final Year | Working model or guided build, Circuit diagram and bill of materials, Firmware / code with explanation | from ₹9,999 + components |
| Capstone Project (CPE) | Working project or model, Black book in MSBTE format, Step-by-step explanation | ₹9,999 + components |
| Diploma ITR | 100% working source code, Project report PDF, PPT | ₹1,999 + components |
No GST and no hidden charges. Use the cost calculator for a quote with your deadline and add-ons, or see all plans.
Download the project brief (PDF)
Summary, working, components and cost and viva questions on one branded PDF to show your guide or team. To get it developed, contact us on WhatsApp.
What you submit with this project
- Working model with circuit diagram and program code
- Project report or black book in your university's chapter order (block diagram, circuit, calculations, results)
- Presentation for the review and final viva
- Synopsis for topic approval, if your college asks for one
Electrical viva questions on this project
What is the aim of the Solar Power Bank with Wireless Charging project?
A folding solar power bank with wireless charging. Solar panels charge a lithium battery pack through a charge controller, and phones charge by wire or wirelessly through built-in coils.
Explain the working of your project in short.
Rechargeable battery and Solar panel supply the circuit; a regulator gives the controller and sensors a steady 5 V. The Arduino Uno R3 reads the inputs, runs the decision logic written in C/C++ and drives the outputs. The LEDs indicate status.
What microcontroller is on the Arduino Uno and what are its key specifications?
The Uno uses the ATmega328P: 8-bit, 16 MHz clock, 32 KB flash, 2 KB SRAM, 14 digital I/O pins (6 PWM) and 6 analog inputs with a 10-bit ADC.
Why is a resistor connected in series with an LED?
It limits the current to a safe value (about 10–20 mA). Without it, the LED would draw too much current and burn out. R = (supply voltage − LED voltage) ÷ current.
How do you calculate battery backup time?
Backup time (hours) ≈ battery capacity (Ah) × voltage × 0.8 efficiency ÷ load power (W). For example, 12 V 7 Ah at 20 W gives about 3.3 hours.
What is the efficiency of a typical solar panel?
Commercial polycrystalline panels convert about 15–17% and monocrystalline about 18–22% of sunlight into electricity. Output depends on sunlight, angle and temperature.
Why is a charge controller needed?
It regulates the charging voltage and current, cuts off when the battery is full and prevents deep discharge, which protects battery life.
How did you calculate the power rating of your system?
Using P = V × I for each load, adding a margin of 20 to 25%. The solar panel is sized from the daily energy need divided by about 5 peak sun hours in India. Battery capacity is the energy needed per day divided by the battery voltage and allowable depth of discharge.
What protection have you provided in the circuit?
A fuse against short circuit, relays or optocouplers to isolate the control side from the power side, flyback diodes across inductive loads such as relays and motors, and software limits that cut off on over-current or over-voltage.
What is the efficiency of your system and how did you measure it?
Efficiency = output power ÷ input power × 100. We measured input and output voltage and current with a multimeter at different loads and tabulated the results in the report.
Explain the block diagram of your project.
The input section senses the real-world quantity, the Arduino Uno R3 processes it according to the program, and the output section displays the result and drives the actuators. The power supply section feeds every block.
Related projects
Academic use: Project Buddyy offers mentoring, guidance and reference material for learning. You stay responsible for following your institution's academic integrity rules and for understanding everything you submit.
Want to build Solar Power Bank with Wireless Charging?
Send your college, deadline and team size. We confirm the scope, cost and what you will submit.